Rate this post

If you did not activate the label taken sensor to detect the removal of the dispensed peeled label with software commands, the printer will stack and eject peeled labels. Go to My Zebra. Page 25 The roll must not sit in the bottom of the media compartment. Pull the left side of the ribbon guide out. Sensor Cleaning Use a dry swab to remove any residue that may be left from the first cleaning. To return to auto calibration, default the printer refer to the four-flash sequence in Feed Button Modes on page 80 in this section. Page 95 Serial Port Interface

Uploader: Nikozil
Date Added: 7 August 2011
File Size: 63.35 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 83757
Price: Free* [*Free Regsitration Required]

Don’t have an account? Page hk420t An empty roll core of the same width as the stack of zebra technologies ztc gk420t fan-fold media can be placed between the roll holders to provide additional support for thin media. Your Printer You must observe static-safe procedures when working with the printhead zebra technologies ztc gk420t the electronic components under the top cover.

Load a new ribbon roll and empty ribbon core. This manual also for: Open the media roll holders. Experiment with these settings to gkk420t the optimal mix for your application. Release the Feed button. List Font Links Prints a list of the linked fonts Font Identifier Assigns a single alphanumeric character as an alias to a font stored in memory.

Find manuals, firmware, drivers, utilities, software zebra technologies ztc gk420t knowledge articles. Open a ticket or track an existing repair in one of Zebra’s repair portals. Refer to the power off mode procedure in Feed Button Modes on page 80 in this section.

Printer Options Zebra technologies ztc gk420t Dispenser Option Lift the liner over the top of the printer and open the dispenser door. Load your labels into the printer. Gently but firmly pull the green zebra technologies ztc gk420t wire off the printhead. Press a corner of the sticky side of the label to the outer surface of the roll of ribbon.

Rub the cleaning pen across the dark area of the printhead. Pull the media guides open with your free hand and place the media roll on the roll holders and release the guides.

Platen Bearings Rev. Refer to the one-flash sequence of Feed Button Modes on zebra technologies ztc gk420t 80 to print this label. Maintenance Replacing the Printhead The cabling and unique parameters for each of these physical printer communication interfaces is discussed in the following pages to assist you with making configuration setup choices prior to and immediately technollgies applying power.

First, make sure that the correct communications port USB on the computer is selected. The KDU is strictly a terminal and does not have the capability to store data or set up parameters.

Select the coverage plan that best suits the needs of your business.

GK420t Desktop Printer Support

Comments to this Manuals Your Name. Open the cover and dispenser door. This will move adhesive transferred from the edges of media to the printhead outside of media path.

After Your Printer is Connected Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. An empty roll core of the same width as the stack zebra technologies ztc gk420t the fan-fold media can be zebra technologies ztc gk420t between the roll holders to provide additional support for thin media.

Support Content Migration

Adjust the media guide stop position with the green thumb wheel. Push the media under both of the media guides. Page 73 Adhesives and oils, for example, may be thinned by the initial cleaning but not completely removed. Rotate the wheel away from you to zebra technologies ztc gk420t the media guide narrower. Table of Contents Add to my manuals Add.

A cutter can be used to cut apart individual labels. Wait one minute before closing the printer. Page technplogies Zebra Technologies has been advised of the possibility of such damages.

Support and Downloads | Zebra

About This Document Document Conventions These are typically used by Zebra Tech Support to diagnose printer problems. Push the right side printhead wire connector onto the printhead.

Go to My Zebra. Page 27 You can find your first ribbon take-up core in the packing box.

Repeat steps 1 and zebra technologies ztc gk420t as required until all residue and streaks are technologiss from the sensor. Peel a label from its liner. Replacing The Printhead Use a small flat bladed screwdriver to remove the ribbon guide. Feed Button Troubleshooting chapter. The print server provides you with a browser interface for printer and print server settings. Printing On Fan-fold Media Adjust the media guide stop position with the green thumb wheel.

Access development tools and collaborate with other application developers.